Excerpts

After adding SBS latex, the G’ and G” values of the modified asphalt both underwent an increasing trend compared with the neat asphalt.

For both alloys, we obtained a clear trend.

As shown in Figure 8 , with the heating rate increasing from 0 to 20 °C/min, the apparent porosity possesses an increasing trend; however, when the heating rate further increases to 30 °C/min, it decreases slightly because of the pores’ shrinkage caused by the hydration of the matrix surrounding the pores [ 35 , 40 ].

There is a clear trend of decreasing mechanical properties by FSW process.

Two-layered reinforcement caused a highly significant increase in density, leading to the p -value of 0.000 for all three variants compared to the control plywood.

For a certain porosity PTFE/Al energetic material, as the strain rate increases, the yield strength, compressive strength, and failure strain of the material all show an increasing trend.

In contrast, the creep curves for the testing temperature higher than 450 °C show an increasing trend, rather than a steady stage at the end of the creep curve.

It can be seen from the table that the densities of the foam materials presented an increasing trend with the increase of the fiber addition amount.

During this process, the load curve showed a trend of gradual decline.

From Table 9 , we observed that, with the increase of age, the strength of the specimens showed a trend of increase, but the crack in Zhejiang and the strength of the emulsified asphalt cold recycled of specimen preparation always failed to reach a high emulsification.

As for the lower half, although the coagulation of powder was quite significant, its morphology was much better compared to the upper half.

The highest modulus and hardness were measured in materials irradiated by 132 kGy, while the materials exposed to higher radiation levels displayed a decreasing trend in the aforementioned properties.

A clear trend of ash content rise with the increase of temperature and the process duration is visible.

Ordered 5 wt% Ce-MSG shows a decreasing trend of HRTEM measured pore size compared to ordered undoped-MSG ( Table 1 ), however it exhibits a higher BJH measured pore size ( Table 2 ).

The p value of CD is less than 0.0001, indicating that the interaction of CD is extremely significant.

Contrary to the impacts on the metal surfaces, i.e., brass blocks in this study, the impacts on granite and rubber blocks showed an increasing trend of COR values with increasing grain size.

The highest flexural strength shows a decreasing trend of NCC > CNTs > nano-SiO 2 at both 7 d and 28 d, and the intensity of the CNTs group changes with the dosage is larger than that of the nano-SiO 2 and NCC groups.

The water absorption rate ranking of the CNTs group is 0.1% < 0.01% < 0% < 0.5% < 2% < 3%, an overall trend which is the opposite of the compressive strength one, indicating that CNTs also have a good filling effect on the internal pores of mortar specimens.

The copper signal for this layer (in the case of a coating fabricated at the voltage of 450 V) is almost constant in depth, whereas a decreasing trend for Cu is observed for higher voltages (550 V, 650 V).

Thus, the relationships between amplitude parameters and the variables ( p and r ) are significant, in other word, the model is highly significant. 3.2.

It is found that the load sharing ratio of anchor showed an increasing trend but a slower and slower upward trend with the increase of landslide thrust, especially when the load sharing ratio of anchor is more than 20%.

As the content of the amorphous phase increases, the hydration activity of the slag shows an increasing trend, but the growth rate is related to the chemical composition of the slag itself.

The anode to cathode flow showed a trend of increasing firstly and then decreasing, which is different from the results of most electro-osmosis studies [ 42 , 43 , 44 , 45 ].

Over the recent years an increasing trend of consumer products which contain NPs became evident.

Interestingly there is no increase in collagen deposition over 21 days in the GM group but an increasing trend in deposition is seen following the addition of osteocyte secreted factors.