Excerpts

However, as the temperature increased to 378 K, the RMSD values rose to 0.871 Å for silk I and 0.843 Å for silk II, reflecting a clear trend of increasing structural deviation with temperature.

As corrosion progressed, the weight loss in the presence of bacteria was consistently greater than that in a sterile environment, with all three types of steel showing an increasing trend in weight loss.

This indicates that an increase in Cu content could effectively inhibit the accelerated corrosion by bacteria, with a clear trend that higher Cu content yielded more significant inhibition effects. 3.2.

Precast concrete structures have become an important trend in the current construction industry, bringing significant advantages in improving construction quality, saving costs, and shortening construction periods.

Above 1033 K, microstructures are composed of the τ 1 and FeSi phases with a decreasing trend in the FeSi phase fraction.

As the pH increased, the flat band potential (E fb ) generally exhibited a decreasing trend.

For example, in this study, the AAFs in the Z-direction show an increasing trend with elevation, while in the study by Jiang et al.

Partial significance was found for S a and S z , with some exceptions: 10× and 20× for S z and 20× and 50× for S a .

Additionally, the table highlights a notable trend where compounds incorporating urea (entries 1–3 in Table 2 ) achieved higher yields and faster reaction completions compared to those involving thiourea counterparts (entries 4–6 in Table 2 ).

From the results of the pore property analysis, an increasing trend with an increasing impregnation ratio from 0.5 to 2.0 was observed.

In the previous studies [ 10 , 11 ], the pore properties of the resulting carbon products prepared from oil-containing residue through the physical activation of carbon dioxide (CO 2 ) at 850 °C for 0.5–1.5 h showed a decreasing trend [ 11 ].

It can be seen from Figure 3 a that the material showed a trend of brittle fracture after reaching its elastic limit under the action of a tensile load.

With the increasing number of strokes, chip adhesion becomes more severe, diminishing the oilstone grinding capability, thus leading to a decreasing trend in the change of hole diameter.

Compound 4 has an MW = 936.2 mg/mmol; therefore, the adsorbed amount of DES is quite significant (on a gravimetric basis): 100% × 342.8 mg DES/936.2 mg compound 4 = 36.6 wt. % or 366 mg/g.

For example, in the case of CBP-R/R, an increasing trend can be observed.

With the gradual decrease in ambient pH, these sensors showed an increasing trend at A 650 /A 530 .

An analysis of the effect of the carbonization temperature on pore size reveals a significant trend: the number of micropores increases with higher carbonization temperatures.

There is an evident trend of increasing strain at the break with the increase in the time of exposure to the aqueous environment.

The shear strength, cohesion, and internal friction angle of vegetation concrete all showed a decreasing trend with increasing foaming agent content.

Figure 7 e illustrates that C 0 exhibits a decreasing trend with frequency in the 2–18 GHz band, accompanied by considerable fluctuations.

However, the monoclinic phase fraction was lowest at 2 mol% CeO 2 doping, and it showed an increasing trend as the doping concentration increased beyond that.

Authors seek effective thermal conductivity coefficients for practically relevant structures, assuming random distributions of the filler [ 11 , 12 , 13 ], or analyze thermal conductivity of new practically significant materials [ 14 , 15 , 16 , 17 ].

Cantabro Test The data presented in Figure 10 illustrate a clear trend where the loss rate correlates with chloride salt concentrations and erosion duration.

In order to determine the effect of f z on h min , a trend line was introduced on the graph, which shows that as the feed per tooth increases, the value of the h min parameter shows an increasing trend.

Analyzing the popularity of recurrence techniques since 2000, one can observe an increasing trend in the cutting of composites and other modern materials.