Excerpts

An increasing trend was observed with the increasing dosage of Mn 2+ when MnCl 2 was added first, compared to that without MnCl 2 addition.

In addition, the adsorption of NaOL on scheelite showed a decreasing trend, indicating that the increase of Mn 2+ dosage would inhibit the flotation of scheelite.

The furrow marks on the wear surface became shallow with the increasing Ti content, and the adhesion area (black area) displayed a decreasing trend.

From Table 6 , Table 7 , Table 8 and Table 9 , it can be found that laser power and layer thickness showed a quite significant impact on the sinking distance and overhanging surface roughness of square-shape inner structure while defocusing amount and scan speed showed less impact compared to the above-mentioned process parameters.

In Y 1 , the first-order terms X 1 and X 3 have extremely significant effects on the results; in Y 2 , the first-order terms X 1 and X 3 have extremely significant effects on the results, the interaction terms X 1 × 2 have significant effects on the results and the quadratic term X 22 has significant effects on the results. 3.2.2.

It can be seen from Figure 6 a that RMSE showed a trend of first decreasing and then increasing with the increasing number of iterations, R 2 showed a trend of first increasing and then decreasing with the increasing number of iterations, and the network performance reached the best when the number of iterations was 3500.

The 3-day and 7-day compressive strengths of the machine-made sand showed a trend of increasing and then decreasing with the increase of stone powder content.

With the increase in powder content from 1.2% to 4.0%, chemical bond G d and friction bond τ 0 showed a decreasing trend.

With the increase in the differential dosage from 1.2% to 4.0%, the obvious “peak and valley” before reaching the maximum load showed a trend of first increasing and then decreasing.

Such dependence was typically ignored in previous works but may be significant at high irradiation doses, as we demonstrate with basic TTM calculations for ruthenium, palladium, and gold elemental metals.

The strength of the Al-Si-Cu-Mg alloy showed a trend of first increase and then decrease, and the best effect was achieved when the Cd content was 0.3% [ 9 , 25 ].

However, the critical failure strain shows a decreasing trend with the increased W content.

The linear slope of yield strength with respect to strain rate shows a slightly increasing trend with increasing W content, indicating that the sensitivity of the materials to strain rate increases slightly with increasing W content.

The stress triaxiality shows an increasing trend upon continuous loading.

The CMS and TS tests both indicated an increasing trend in progress over time.

The average grain diameter exhibits a decreasing trend compared with the rail steels 1911 and 1921, which have the microstructures of reticular ferrite and pearlite.

It should be noted that the diffraction peaks of AFt decreased with increasing of LBD fineness levels, while diffraction peaks of C 3 A·CaCO 3 ·11H 2 O show an increasing trend, this means that during the hydration reaction process, AFt was partially converted into AFm, while CaCO 3 could react with C 3 A to form C 3 A·CaCO 3 ·11H 2 O.

Therefore, the front part of the fitting lines of Cr, Ti and Zr elements shows a decreasing trend.

As the WC size increased, the bonding between the splats improved ( Figure 4 ); thus, it exhibited an increasing trend for both the nanohardness and Young’s modulus in the cross-sections of the coatings.

With the increase of Factor E, VSI showed a trend of increasing first and then decreasing.

With the increase of PS content, CS at different ages showed an increasing trend.

Moreover, the TSR results given in Figure 5 below shows an increasing trend for mixes with fibers.

Whether the amplicons of one taxa will be suppressed over those of others and whether a definite trend will be deducible from these effects, such as that predisposing microorganisms with certain phenotypic features to be affected more than those with others, are some of the questions that this study has attempted to answer.

The removal rate of Mg from the samples showed an increasing trend as the addition dosage increased.

At 7 days after implantation, iNOS positive cells in each group showed a decreasing trend, while CD163 positive cells revealed an increasing tendency ( Figure 8 C,D) compared with those at 3 days after implantation ( Figure 8 A,B).