Excerpts

The applications of these systems display an increasing trend in both the R&D and industry sectors.

The T mc measurements in all the masks in this style exceeded those of the other styles at a highly significant level.

The red saturation had an increasing trend when the separation period and cycle were increased.

However, at 7, 14, and 28 days, all the mortars with 7% of coarse silica fume followed a clear trend, i.e., the higher the limestone content, the lower the flexural strength.

p < 0.05 was adopted as significant, and p < 0.01 as highly significant. 3.

With enriching the Cu element and depleting the Ni content, the hardness shows a decreasing trend.

Nanoparticles have a worldwide use, with an increasing trend in production every year [ 15 ].

Specific Heat Capacity Heat capacity ( Figure 11 ) exhibited an increasing trend with rising temperature, as expected by the Debye model.

With the increase in calcination temperature and sintering time, the content of C 3 S increased gradually, and the content of C 2 S in each sample showed a trend of first increasing and then decreasing.

The results of the analysis of variance of the data related to fiber length are shown in Table 2 , which demonstrates that the influence of cotton varieties (V) and cotton regions (R), as well as interactions, were highly significant in this study.

The differences in results between the 25° and 30° system were small, but there was a decreasing trend.

In addition, the characteristics of B x signals, the mean value, and the peak value of the average of B x had an extremely significant linear relationship with the applied fatigue stress during the stable stage of the fatigue test, which indicates that MMMT is a feasible method for fatigue stress evaluation and even residual fatigue life estimation for weldments in service. welded joint tension-compression fatigue test metal magne

The decrease in the workability is highly significant in the lower water–cement ratio because of higher water absorption [ 44 , 50 ].

On the other hand, there was a decreasing trend of hue change with increasing cellulose content that could be observed.

The statistical regression prediction models were established as follows. (9) M T D = 4.1531 A I a − 0.1121 T F a − 3.6846 R 2 = 0.89 (10) M P D = 6.7514 A I a + 0.4139 T F a − 6.4471 R 2 = 0.93 (11) W F C = 0.1001 A I a + 0.0453 T F a + 0.6405 R 2 = 0.69 The three regression models above were tested by the F-tests and were highly significant statistically at a significance level of 95%.

The box fractal dimension also showed a decreasing trend.

The compressive strength and tensile strength showed an increasing trend with the increase in SF.

It can be seen that the YL intensity had a great relationship with the substrate, and the intensity of YL band follows a decreasing trend: C > 2M > 4A.

Strength shows an increasing trend with increasing roughness.

It was also found from simulation that with an increase in ball impact angle, the maximum residual compressive stress, the depth of maximum residual compressive stress and the depth of the residual compressive stress layer were significantly improved; an exception was the surface residual compressive stress, which showed a decreasing trend.

The swelling index of 2.0 phr MPP-filled NR latex films was comparable with the control sample, while ZnO NP-filled NR latex films displayed a decreasing trend in the swelling index when the loading increased.

For a feed rate of 0.16 mm/tooth, there was a slight decrease in RSm to 0.027 mm, followed by an increasing trend.

The parameter maximum peak height of the roughness profile Rp in the feed rate range 0.02 ÷ 0.06 mm/tooth ( Figure 9 a–c), showed a decreasing trend, from a maximum value of 0.818 μm to 0.552 μm.

Complex INPs The production of particles with an optimal ratio of magnetic properties and antibacterial activity has seen an increasing trend in recent years.

The surface roughness value of the vertical-plane showed a trend of first increasing and then decreasing with an increasing current density, and the roughness was the largest machined at 10 Acm −2 , which was 42 μm.