Excerpts

The results of the analysis of variance of the data related to fiber length are shown in Table 2 , which demonstrates that the influence of cotton varieties (V) and cotton regions (R), as well as interactions, were highly significant in this study.

The differences in results between the 25° and 30° system were small, but there was a decreasing trend.

In addition, the characteristics of B x signals, the mean value, and the peak value of the average of B x had an extremely significant linear relationship with the applied fatigue stress during the stable stage of the fatigue test, which indicates that MMMT is a feasible method for fatigue stress evaluation and even residual fatigue life estimation for weldments in service. welded joint tension-compression fatigue test metal magne

The decrease in the workability is highly significant in the lower water–cement ratio because of higher water absorption [ 44 , 50 ].

On the other hand, there was a decreasing trend of hue change with increasing cellulose content that could be observed.

After the initial reading, crystallinity revealed a decreasing trend up to 24 h.

It can be seen from Table 8 that the error between the predicted and the measured value shows a decreasing trend with the adaptive evolution algorithm, about 2% to 8%.

For Al 2 O 3 activity, it presents an increasing trend as basicity increases, which may mean that alumina, as a neutral oxide, exhibits complex changes in different acid and alkaline environments.

Strength shows an increasing trend with increasing roughness.

From Figure 3 for the results for all wood images, we can see a clear trend that observers found higher elevation prints more natural than flatter ones.

The swelling index of 2.0 phr MPP-filled NR latex films was comparable with the control sample, while ZnO NP-filled NR latex films displayed a decreasing trend in the swelling index when the loading increased.

For a feed rate of 0.16 mm/tooth, there was a slight decrease in RSm to 0.027 mm, followed by an increasing trend.

The parameter maximum peak height of the roughness profile Rp in the feed rate range 0.02 ÷ 0.06 mm/tooth ( Figure 9 a–c), showed a decreasing trend, from a maximum value of 0.818 μm to 0.552 μm.

Complex INPs The production of particles with an optimal ratio of magnetic properties and antibacterial activity has seen an increasing trend in recent years.

The surface roughness value of the vertical-plane showed a trend of first increasing and then decreasing with an increasing current density, and the roughness was the largest machined at 10 Acm −2 , which was 42 μm.

It can be seen from the analysis of variance in Table 3 that the p -value of the liquid flow rate, CPCM thickness and the cross-sectional area of the pipe is less than 0.0001, indicating that the impact on T max of batteries is highly significant.

The p -value of the model is also less than 0.0001, indicating that this model is extremely significant, so this model can be used to accurately predict the changes in T max of the battery module.

Introduction In today’s food packaging field, there is an increasing trend to replace non-degradable plastic packaging materials using annually renewable natural biopolymers to solve the problems of environmental pollution and resource depletion caused by the use of synthetic plastics [ 1 , 2 ].

All results of G*/sin δ presented an increasing trend with the addition of CRM, which is recognized to be similar to that of the original G*/sin δ as shown in Figure 7 .

G*sin δ value for CRM binders was observed to have a decreasing trend with increasing CRM content.

%rec results showed a trend almost similar to J nr ; the addition of CRM positively affects the rutting property, and %rec increased with the addition of TPU into the CRM binder.

At the age of 7 d, the compressive strength increased with the increase of Ca(OH) 2 dosing; while at the age of 28 d, the compressive strength showed a trend of increasing and then decreasing with the increase of Ca(OH) 2 dosing.

With the increase in the sample width, the T 1 shows a decreasing trend, indicating that the increase in the crack initiation energy has an inverse correlation with the increase in the sample width.

With the decrease in IOTs admixture, the overall 28-day compressive strength of concrete showed an increasing trend.

Flexural Strength—Fiber Volume-Mixing Ratio Curve As can be seen from Figure 3 , with the increase in the volume-doping ratio of various fibers, the flexural strength of PUC at each temperature showed a trend of first increasing and then decreasing.