Excerpts

The fractal dimension also showed a trend of decline.

Thus, concretes with modifying additives and volumetric fiber reinforcement show more than 30% increase in flexural strength, which is a highly significant indicator, as the improvement of deformation properties and cracking resistance of concrete by using dispersed reinforcement with polypropylene fiber was the ultimate task of this study.

The augmentation peak intensity corresponded to m -ZrO 2 and t -ZrO 2 , and a decreasing trend is observed for β -Ca 3 (PO 4 ) 2 .

After 80 days of UV irradiation exposure, a significant decline in the macroscopic mechanical properties occurred in the longitudinal direction, with the largest decrease of 23% in longitudinal compressive strength and a decreasing trend in the transverse mechanical properties at the later stage of aging.

V-Notched Rail Shear Test Results and Discussion The in-plane shear strength/modulus showed an increasing trend at the beginning of aging as shown in Figure 18 .

Then, a negative trend appears due to the agglomeration problems.

The elevated ridges were reduced when a low VED (63 J/mm 3 ) was used for melting the last layer, and generally had a decreasing trend with increasing the hatch angle rotation and the number of the last layers melted.

The graph has an increasing trend.

There is a decreasing trend, except in the 2.2 m and 3.0 m models.

With RCB substitution ratio in CSM, the MDD of CSM decreased gradually, while the OWC showed an increasing trend.

For any density of the GLECC mixtures, as the fiber content decreased, the flow diameter showed an increasing trend.

With the increase in FAC proportion, the compressive strength showed a decreasing trend.

As the mass fraction of La 2 O 3 increases, the depth and width of the groove show a decreasing trend.

The worn surface topography of each sample shown in Figure 11 verifies that, as the mass friction of La 2 O 3 increases, the wear resistance and wear reduction of AM alloy show an increasing trend.

In a very similar manner, the ternary mixes also showed a decreasing trend of strengths both at low (WSA25SF5) and high (WSA40SF10) blends of cement substitution, and the significant increase in strength was obtained for the moderate ternary blend of 33% WSA and 7% SF (WSA33SF7).

However, the diffuse degree of texture showed an increasing trend.

Especially when a p value Prob > F is less than 0.01, the influence factor has an extremely significant effect on WCA.

Figure 9 shows a positive correlation between q u and curing period of RMLS that there is an increasing trend of q u with the increase of curing age when D R is fixed.

With the growing hydration degree, the bulk modulus, shear modulus, and elastic modulus of the cement paste all show an increasing trend, and the differences between these parameters also increase gradually.

With an increasing trend, more than 324,000 patients have received a cochlear implant worldwide [ 1 ].

The oil phase in the oil-in-water emulsion is no longer completely coated, and the coating rate of the phase change material no longer increases, showing a decreasing trend. 3.2.

It was also found from simulation that with an increase in ball impact angle, the maximum residual compressive stress, the depth of maximum residual compressive stress and the depth of the residual compressive stress layer were significantly improved; an exception was the surface residual compressive stress, which showed a decreasing trend.

The compressive strength of MF/SiC NWS showed a decreasing trend with increasing test temperature, but when the test temperature increased to 1400 °C, the compressive strength of MF/SiC NWS was still up to 0.45 Mpa, with strength retention of 96%, indicating its excellent thermal stability in high temperatures. 4.

It is commonly known that the twisting moment and warping moment coincide in the case of thin-walled open sections such as I-beams, and their mutual influence on the cross-sectional stress distribution might be significant.

The milling load shows an increasing trend with the increase of the milling depth a p and the feed speed v f , and the influence of a p is more obvious.