Excerpts

For higher temperatures, oxidation may be significant [ 38 ], and this is why the oven baking process was conducted up to 350 °C, and not in higher temperatures.

(3) The change character of S parameter in candidate steels with increasing irradiation doses was not obvious as the Fe + showed a trend towards a clear saturation.

Therefore, as the ratio of TEOS increased, the stability of silica/MMT showed a decreasing trend.

The thermal expansion coefficient α is both theoretically and practically significant and is essential for the thermodynamic equation of state.

All four of these plots show a clear trend: the d F / d T and d μ / d T sensitivities increased progressively as the average temperature and absolute humidity fell, and with good consistency between the results for the two sections of the G5 string (green and lime).

Furthermore, musicians are finely-tuned to small details of the behaviour of their instruments, so that quite subtle aspects of the string behaviour may be significant.

It was found that with an increasing EG/P content, a decreasing trend in the flexural and compressive strength was observed.

The current density has an increasing trend as the applied anodic voltage increases.

Using the voltage and the hot and cold side temperatures to calculate instantaneous value of Seebeck coefficient reveals an interesting trend of the Seebeck coefficient for both transient and steady state conditions.

We observed an increasing trend for the density and compressive strength of the mortar as the collection depth of the sample increased.

αHH significantly hardens at an early age, and after reaching maximum strength, the strength shows minimal change or a decreasing trend; this has been verified in previous studies [ 15 , 16 ].

As a result, the hole profile becomes increasingly steeper, and the hole taper shows a decreasing trend with respect to the laser power within the selected range.

Such an increasing trend is not a rare phenomenon, such as the Pb 0.94 La 0.04 [(Zr 0.7 Sn 0.3 ) 0.9 Ti 0.1 ]O 3 ceramics prepared by the solid-state reaction method reported by Xu et al., where apparent exponential elevation of the energy-storage density is observed above 60 kV/cm [ 19 ].

For the studied lithotypes, there is a clear trend observed within all three test methods to evaluate the efficiency.

However, a clear trend and prediction for higher concentrations like 25 wt% can be drawn. 2.2.2.

The introduction of boric anhydride creates a moderately significant impact on the strength of the engineered cementitious composites.

Particularly, often they are mentioned together with NIRF (Near Infrared Fluorescence) using the dye Cy5.5 (Cyanine 5.5)-SPION system [ 45 ], but also CT (Computed Tomography), PET (Positron Emission Tomography), and SPECT (Single Photon Emission Tomography) are possible to be used in combination with MRI when applying SPIONs as a multimodal contrast [ 46 ] Finally, there is an increasing trend to use SPIONs in diagnostic and clinical techniques.

After 250 cycles, the Rct and W of the Cel-CS showed an increasing trend to a smaller extent, while that of Cu-CS showed an obvious increase, implying better structure stability of the Cel-CS electrode.

However, in a two-step foaming process, in which there is a finite time between the depressurization and the foaming, the skin thickness may be significant.

The packing porosity was deliberately given as 0%, 20%, 40%, and 60% in an increasing trend.

As can be observed from the figure, the specific wear rate shows an increasing trend for both WC samples with an increase in temperature.

For the ABS BM FDM, it showed a clear trend of increasing by 17% in the mechanical performance when increasing the number of contours from two (ULSF: 1410 ± 71) to 22 (ULSF: 1682 ± 63).

It was a little different from the experimental scheme and showed a trend that with a high Te addition, the S content declined a little.

It can be seen from Figure 7 that the change in stress with time shows a tendency to increase sharply and then slowly decrease, while the subsurface damage depth always shows an increasing trend, and the increasing rate (slope) is basically kept the same.

Interestingly, the residual strength of the GRAC showed a trend of first increasing and then decreasing with the increase of exposure time.