It can be seen from Figure 16 that under dynamic tensile conditions, although the SCAC specimens with typical splitting failure did not break completely, the failure morphology of SCAC specimens showed a trend in which the particle size of the broken slag decreased, with the amount of broken slag increasing, as well as breaking more thoroughly, with increasing strain rate grade.
Excerpts
a clear trendgold
Moreover, it is difficult to establish a clear trend for the Ssk parameter, as even though some results take positive values, most are negative values, which may indicate a plateau-like nature of the hills.
An expected trend of reduction in capacitance with increase in scan rate was observed for all materials.
Moreover, the C value presents a decreasing trend, the Curie–Weiss temperature increases first and then decreases, and the temperature above which the Curie–Weiss law can be obeyed (T CW ) shows an increasing trend with increasing sintering temperature, i.e., the temperature difference of T CW -T m is 11–27 °C for different samples.
As the temperature increases (100–200 °C), the order degree of the wear surface and friction-transferred film rises significantly (I D /I G shows a decreasing trend with the increase in temperature), resulting in the decrease in COF and frictional shear stress, which is conducive to reducing the wear of the two types of graphite.
With the increase of water–cement ratio and dosage of foaming agent, thermogravimetric data showed that the carbon dioxide sealing capacity showed a trend of first increasing and then decreasing.
a notable trendgold
The figure illustrates a notable trend where the final oil recovery rate remains relatively low at lower water injection rates.
The specific capacitance value calculated from the GCD curve was found to be 502.97 Fg −1 for Nb 2 CT x at the current density of 1.0 Ag −1 , and it exhibited a decreasing trend up to 165 Fg −1 at the current density of 4.4 Ag −1 , as shown in Figure 6 d,e.
The difference in the number and parameter values of acoustic emission events before and after uniaxial compression fracture of 0.7 mm and 1 mm fractured sandstone samples is quite significant, with the difference in order of magnitude ranging from 10–1000.
When n(CO): n(DM) was in the range of 1:3–1:5, COQS yield showed an increasing trend with the increase of n(DM) ( Figure 2 c), and when n(CO): n(DM) was in the range of 1:5–1:8, too much DM will interfere with the catalytic performance of the catalyst, leading to a significant decrease in COQS yield.
It was proven by the quite significant increase in C-H bond intensity of the rHIPS samples at around 3000–2840 cm −1 after experiencing more reprocessing steps.
The FEM result shows that the temperature of the workpiece displays a decreasing trend from the HAZ to the BM.
Mechanical Property Losses When analyzing the graphs in Figure 4 , a decreasing trend for the mechanical properties of all the concrete families as a function of ASR-induced development is clearly observed.
The overall damage zone presents a decreasing trend with the increase of in-situ stress, because the tensile damage is more sensitive than the compressive damage for rock material.
Moreover, the swelling ratio of C/G3 hydrogel has been exhibiting an increasing trend, which is due to the hydrolytic breakage of ester groups dominating the alkaline environment, lessening the extent of cross-linking and making the hydrogel of the network structure looser, giving rise to a noticeable augment in the swelling ratio.
Nonetheless, the removal ratio will exhibit a decreasing trend. 3.7.4.
a slight trendgold
For the premolar segments of the Bio-Active ® archwires, a slight trend of increasing Af temperature with increased duration of use was observed.
Although the average diameter of nanofiber shows an increasing trend with the increase in feeding rate, the change is not obvious.
As depicted, with the increase in HGM content, the thermal conductivity of the composite material shows a decreasing trend.
As shown in Figure 9 , the elastic modulus of the composite material shows an increasing trend with the increase in HGM content.
This indicates that although the internal stress of the sample decreases for a while at the occurrence of plastic deformation, it soon shifts to an increasing trend.
[ 24 ] reported that the derived relationship between the damage variable and electrical resistivity is well correlated with the experimental data, in which electrical resistivity showed a trend of decreasing first and then increasing.
The GB parameters, including the donor concentration (N d ), showed an increasing trend in the range of (3.33–7.64) × 10 17 cm −3 with increasing sintering temperature due to ZnO dissociation.
From the results, it can be found that the tensile strength of the UHPC matrix will show a decreasing trend with the decrease in cement content.
However, it should be noted that the fluorescence intensity of the composite substrate reached a large value when grafting time was 3 h and then showed a decreasing trend with a further increase in grafting time.