Excerpts

However, beyond these moisture thresholds, the curves demonstrate a decreasing trend when the moisture contents of pebbles and sand are greater than 0.75% and 10.9%, respectively.

Both TTF (median 720, 643, 562, 406, 254 s) and the NCF (3600, 3215, 2810, 2032, 1482 cycles) decreased in the following order RM_06 > RPB > RM_04 > Proc > WOG with partially significant differences.

(2) The mass loss rate generally showed a trend of decreasing first and then increasing.

Investigating various approaches to realize P-SE is highly significant for enhancing the E ff of solar cells and reducing energy consumption. 2.

It is observed that the inflection point concentration exhibits an increasing trend with the augmentation of laser power.

The represented and expected amounts, having also a positive trend in increase, undoubtedly indicate the great potential of the use of CDW as a substitute of natural stone aggregate and decrease the need for its exploitation.

In Figure 7 a and Figure 7 b, it can be observed that both dyes exhibit an increasing trend in dye exhaustion (E%) and surface color strength (K/S) over a prolonged time.

It is evident from the figure that with the increase in the amount of CGs, the chloride ion binding rate of the clean slurry specimen exhibits a decreasing trend at both 28 and 90 days.

In Figure 8 e,f, the scatterers display an increasing trend from 1.4 V to 0.4 V, which corresponds to the continued electrochemical reaction of exposed new Bi after the cracking of Bi nanoparticles, resulting in an increase in size.

After the drastic decrease in specific resistance, the specific resistance of all types of Ag NP inks maintained a decreasing trend until 250 °C.

The maximum load Pm shows a decreasing trend with increasing austenitizing temperature, dropping from 44 KN at 940 °C to 33.7 KN at 1200 °C.

Finally, in Stage IV (0.82 < χ ̄ < 0.98), which is, also, of very small duration (equal to about 0.7 s), the load exhibits a decreasing trend, while the average rate m of the change in CC*(χ) increases abruptly towards its global maximum which, for the specific experiment, is equal to about m ≈ 2.6, attained at the instant of fracture.

The values of m are now systematically higher than the m = 1 limit, with an increasing trend, which is initially very weak and then it becomes rapid as fracture approaches.

Maximum Dry Density (MDD) results show an increasing trend as the marble powder content increases.

The sentiment analysis, with an average score of 0.638771, reflects a positive trend in academic discourse and an increasing recognition of the potential of nanocomposites.

The dispersion component shows an increasing trend followed by a decreasing trend.

Conversely, the retarding effect of XANa (PX) shows a decreasing trend, and at 0.15%, it demonstrates a pro-setting effect, reducing the initial setting time by around 79%.

The plots indicate a decreasing trend, followed by an increasing trend in the average friction coefficient and wear weight loss of the composite coatings.

A decreasing trend (change up to 40%) was found in magnetic parameters during embrittlement, regardless of the origin of the embrittlement.

According to Table 3 and Table 6 , with the increase in TM addition, the mechanical properties of Cr 0.47 Al 0.5 TM 0.03 N such as bulk modulus, shear modulus, Young’s modulus, and theoretical hardness exhibit a decreasing trend, while an increase in Cauchy pressure and Pugh’s index of ductility indicates an increased toughness and a tendency toward the mobile character of the bonds, which results in a decreased resistance against shearing.

As rubber particles possess a lower unit weight compared to that of the natural sand, CRGPC exhibits a decreasing trend in density with the increase of the percentage of rubber particles. 3.3.

In particular, it consistently exhibited a decreasing trend.

A clear trend between residual stress and chemical resistance was confirmed in an acid resistance test by using 40% HF [ 75 ] with no appreciable etching after the test for the lowest tensile stress (+41 MPa).

When the strength of the rock block is much higher than that of the matrix, and the block proportion is less than 70%, the uniaxial compressive strength of the sample shows an increasing trend with the increase in the block proportion [ 25 , 26 , 27 ], but when the block proportion exceeds 70%, the uniaxial compressive strength of the sample shows a decreasing trend [ 22 ].

As expected, an increasing trend in austenite vol.% was observed with increasing IAT from 680 °C to 740 °C.