Excerpts

The plots indicate a decreasing trend, followed by an increasing trend in the average friction coefficient and wear weight loss of the composite coatings.

A decreasing trend (change up to 40%) was found in magnetic parameters during embrittlement, regardless of the origin of the embrittlement.

The loss of the Fe-Co alloy in the face of compressive stress shows a decreasing trend [ 27 ].

A clear trend is observed: the adhesion strength decreases as the temperature approaches the ice’s melting point.

On the other hand, Incoloy 825 showed a trend of E p ennoblement with an increasing nitrite content of 0.1 M NaCl, and the weldment underwent greater ennoblement.

However, with the increase in TiCp, the impact toughness and bending strength of the hierarchical composites show an increasing trend first and then decrease; the highest values are obtained at 40% TiCp.

It can be observed that as the deviation angle increases, both the ultimate tensile strength and yield strength show a decreasing trend, while the elongation and cross-sectional shrinkage exhibit an increasing trend.

The T g measurements, recorded using the VTSE technique, showed an increasing trend owing to differences in the molecular weights of the investigated compounds ( Figure 5 ).

Figure 15 displays the specific distribution of void in different zones of each part; for the PFs-enhanced asphalt mixture specimen, the void rate roughly showed an increasing trend from zone 1 to zone 4 for each part.

It can be seen that although the splitting tensile strength of the asphalt mixtures showed a decreasing trend with the increase of dynamic water pressure, there were significant differences in the strength variation characteristics of the three asphalt mixtures.

The results illustrate that while the interfacial properties of the two systems after hygrothermal aging both show a decreasing trend with the growth of aging time, there are significant differences in their specific patterns of change.

According to Table 2 , an increasing trend in the presence of the elements V and Zr can be observed in the BCC phase.

Above this temperature, the higher-filled composites (M2UD10 and M2UD15) showed a trend of lower viscosity, mainly caused by the melting of PLA.

Correlation equations between BTS and Vp are as below: (11) B T S = 0.0013 V p − 0.2022 R 2 = 0.96 for dry conditions (12) B T S = 0.0022 V p − 2.7623 R 2 = 0.98 for saturated conditions As can be seen from the correlation equations developed in Figure 11 , an increasing trend in UCS and BTS with increasing Vp can be observed for the samples under both dry and saturated conditions.

The results presented a clear trend in which the shrinking of these concretes gradually increased with time due to the occurrence of water that escaped from the capillary pores of the OPCC and GPC to the unsaturated outside air.

The p value for compressive strength is less than 0.01, indicating that the regression effect is highly significant.

As the feed ratio of the core–shell increased, the vanillin loading showed an increasing trend.

The weight gain and FR performance of the coated T/C samples demonstrated an increasing trend with an increasing FR concentration ( Figure 7 a).

As shown in Figure 7 b, the compressive strength of SCECC shows an increasing trend alongside the increase in PVA volume fraction, and the rate of increase decreases gradually.

On the contrary, an increasing trend towards more anodic values is observed, probably as a consequence of the pore ion and lower pore pH remaining more stable, as shown in Figure 9 and Figure 10 .

In relation to the delta ferrite content, calculated using the metallographic method, a decreasing trend of delta ferrite content from the face of weld towards root of weld.

After that, with the extension in the aging time, the hardness showed a decreasing trend.

Thus, the optimal single-particle compressive strength of abrasive grains shows a decreasing trend.

However, the differences in crack tip opening loads explain a quite significant influence of the deposition direction on the fatigue life.

The difference in the lattice parameters of the film and the precipitate is quite significant, where the precipitate has an 8.81% increase compared to the thin film in the free region.