Excerpts

It is probably because the change in the f is not large enough in this study so that the limit displacement does not show a significant trend.

Secondly, with the augment of LF-SMB volume ratio, the flow behavior index at each temperature presents a decreasing trend gradually, causing that the asphalt mastics with 0.4 and 0.6 LF-SMB volume ratio cannot reach the flow state whose flow behavior index must be greater than 0.9.

An increasing trend for the magnitudes of both tensile and compressive residual stresses was observed by using larger S ̄ or introducing a chamfer on the cutting edges.

A decreasing trend of median values of the sphericity and convexity parameters with increasing vertical stresses (post-crushing stage) was observed in this study ( Figure 11 a), which was also reported by Zhao et al.

This shift is quite significant in Ni/CeO 2 -Fe 2 O 3 , while it remains limited in CeO 2 -Fe 2 O 3 and doesn’t occur at these temperatures in pure CeO 2 , meaning the partial reduction is enhanced by the addition of Ni, leading to deeper reduction of the oxygen carrier.

In Case II, an increasing trend can be observed.

It is also worth noting that, at a low frequency band, i.e., 3–9 GHz, a decreasing trend can apparently be found for the real part of the permittivity.

Even at a Reynolds number much lower than 1, this efficiency remains quite significant (≈0.3) while the theoretical behavior in Stokes flow is particles avoiding each other at their initial relative positions, which leads to zero efficiency.

Since immunotherapies are becoming an important trend to treat non-communicable diseases, the RAGEp/PSiP vaccine will serve as a useful model in the development of chronic conditions such as Alzheimer’s disease and cancer.

Once NPs, PVDF and DBP were blended, the ε c was found to show a decreasing trend with increasing the testing frequency.

It is interesting to note that the O-Ce bond length initially showed an increasing trend, which became nearly constant for CeZr-2, CeZr-3, CeZr-4, and CeZr-6. 3.2.

Neither the crosslinking procedure nor the mineralization affected the cholesteric collagen microstructures; notably, there was a positive trend toward higher stiffness with increasing crosslink density when measured by cantilever-based atomic force microscopy (AFM) nanoindentation.

Also, the thermal conductivity showed a decreasing trend with increasing temperature because of severe phonon–phonon scattering at high temperature.

On the other hand, topography of La oxide coatings did not shown a clear trend in the R a values with the deposition parameters ( Table 1 ) .

Specifically, for f = 0.10 mm/r, h p showed an increasing trend with v c ( Figure 11 ).

The data reveal that the yield stress and compressive strength of the specimens both present an increasing trend as the strain rate increases.

It is obvious that the nozzle diameter and cylinder ratio had a highly significant impact on the particle size and shape.

Since the diffusion loss might be significant for such small particles, particle concentrations have to be large enough to be sufficient when the aerosol flow reaches the downstream measurement device.

Contrary to other exposure conditions, the decrease in the transmission of degraded samples with exposure time in this case is quite significant.

Really, both velocity and amplitude affect transparency, although amplitude is a near-significant factor.

Moreover, the B / G ratios for the Al–Li–Sc system decrease with the increase of Sc concentration (from 0 to 12.5%), while an increasing trend of B / G ratios is found in the Al–Li–X (X = Co, Zn, and Mo) systems.

Therefore, to comprehensively understand the corrosion mechanism and to predict the corrosion of steel in the oxygen-containing aqueous solution are highly significant.

Similarly, YS exhibits a decreasing trend along 45° and TD.

Finally, an analysis of the features extracted from the time and frequency was carried out to identify a possible trend and a correlation with the surface roughness. 3.

This behaviour is confirmed by the measurements of the hole diameters, which always show a decreasing trend of the measured values for 60 consecutive holes made with the same parameters and tools, as shown in Figure 10 .